IPTV component classification depends on objective characteristics, while customs exemptions turn on notification conditions and import dates.
IPTV set-top box components are classified by their objective characteristics, tariff headings and applicable section and chapter notes, rather than intended use alone. Specifically covered machine parts fall under their own headings; the infrared receiver module falls under 8517.79.90, the band-pass filter and diplexer under 8548.00.00, and the silicone rubber thermal pad under 4016.99.90. Customs exemptions depend on notification coverage, exclusions and conditions: the band-pass filter qualifies only if it is an electronic microassembly, while the diplexer and common-mode choke do not qualify for their claimed benefits. The cable and qualifying vulcanised rubber pad are covered by Notification No. 45/2025-Customs from 1 November 2025, subject to the applicable entry. Earlier imports follow the provisions applicable on their import dates. An advance ruling application remains maintainable where an investigation concerns a different product and the questions raised are not pending or decided in the specified circumstances.
Issues: (i) Whether the applications for advance ruling are maintainable despite a pending investigation concerning another product; (ii) the tariff classification of the specified IPTV set-top box components; (iii) the components' eligibility for the claimed customs notification benefits.
Issue (i): Whether the applications for advance ruling are maintainable despite a pending investigation concerning another product.
Analysis: Under Sections 28E, 28H and 28I of the Customs Act, 1962, an eligible applicant may seek an advance ruling unless the same question is pending or has been decided in the circumstances specified. The applicant held a valid importer-exporter code. The pending investigation concerned heat sinks, which were outside the applications, and no proceeding concerning the questions raised was reported.
Conclusion: The applications are maintainable. The issue is in favour of the assessee.
Issue (ii): The tariff classification of the specified IPTV set-top box components.
Analysis: Rule 1 of the General Rules for Interpretation requires classification by the tariff headings and relevant section and chapter notes. Note 2 to Section XVI directs parts specifically covered by Chapter 84 or 85 headings to their respective headings, with residual classification applicable to other parts. Classification depends on the goods' stated objective characteristics, not merely their intended use. Heading 8543 concerns apparatus having an individual function; the RF filter and diplexer were described as components, while an independent function of the infrared receiver module was not established. The silicone rubber pad was considered under Chapter 40 rather than as a Section XVI part.
Conclusion: The classifications are: antenna, 8517.71.00; audio jack, connectors and DC power jack, 8536.90.90; band-pass filter and diplexer, 8548.00.00; capacitor, 8532.24.00; common-mode choke, 8504.50.10; diode, 8541.10.00; SMD inductor, 8504.50.90; infrared receiver module, 8517.79.90; insulated cable with connector, 8544.42.20; processing, WLAN/Bluetooth controller, load-switch and DC-converter ICs, 8542.31.00; memory ICs, 8542.32.00; audio-amplifier IC, 8542.33.00; linear-voltage regulator IC, 8542.39.00; LED, 8541.41.00; NPN transistor, 8541.21.00; unpopulated PCB, 8534.00.00; film-type resistor, 8533.10.00; tactile switch, 8536.50.90; silicone rubber thermal pad, 4016.99.90; thyristor surge protector, 8541.30.10; transformer, 8504.31.00; and mounted quartz crystal, 8541.60.00. The proposed classifications were accepted except for the infrared receiver module. The issue is partly in favour of the assessee.
Issue (iii): The components' eligibility for the claimed customs notification benefits.
Analysis: Customs exemption depends on the applicable notification's tariff coverage, description, exclusions and conditions; classification or intended use alone is insufficient. The common-mode choke was described as a signal-line interference filter rather than an inductor for power supplies. The diplexer was described as a passive component rather than an electronic microassembly. The band-pass filter's claimed benefit requires qualification as an electronic microassembly, and the thermal pad's benefit requires vulcanised rubber. Notification No. 45/2025-Customs applies from 1 November 2025; earlier imports are governed by the provisions applicable on their import dates.
Conclusion: Subject to the applicable conditions and exclusions, Notification No. 24/2005-Customs covers the specified capacitors, resistors, unpopulated PCBs, semiconductor devices and ICs; it covers the band-pass filter only if it qualifies as an electronic microassembly, but not the diplexer. Notification No. 25/2005-Customs covers the SMD inductor subject to its conditions, but not the common-mode choke. Notification No. 57/2017-Customs covers the antenna and infrared receiver module subject to its exclusions and conditions. Notification No. 45/2025-Customs covers the insulated cable and, if made of vulcanised rubber, the thermal pad, subject to the applicable entry and import date. No claimed notification benefit is available for the audio jack, connectors, DC power jack, tactile switch or transformer. The issue is partly in favour of the assessee.
Final Conclusion: The classifications and notification benefits apply to the goods as described, with eligibility governed by the relevant notification entry and date of import.
Ratio Decidendi: Subject to the applicable section and chapter notes, machine parts specifically covered by a tariff heading are classified under that heading rather than solely by their intended use in a finished machine.