TaxTMI 
TaxTMI 
Effective rate for specified goods falling within one or more Chapters imported for manufacture of specified goods
X X X X Extracts X X X X
X X X X Extracts X X X X
....ed at the rate of 30% ad valorem, subject to the following conditions, namely :- (i) in case of import of goods covered by List B of the said Table, the importer furnishes, at the time of importation, to the Assistant Collector of Customs, an undertaking to the effect that: (a) the said imported goods shall be used for the purpose specified above; (b) the importer shall, within three months or such extended period as the Assistant Collector of Customs may specify in this behalf, produce a certificate from the Assistant Collector of Central Excise in whose jurisdiction the factory manufacturing such finished goods is situated, to the effect that the said goods have been used in the manufacture of the said finished goods; and (c) the importer shall pay, on demand, in the event of his failure to comply with (a) and (b) above, an amount equal to the difference between the duty leviable on such quantity of the said goods but for the exemption contained herein and that already paid at the time of importation. (ii) in the case of goods covered by List C of the said Table, - (a) an officer not below the rank of a Joint Director in the Department of Electronics of the Gove....
X X X X Extracts X X X X
X X X X Extracts X X X X
.... Glass Bulbs/Shells Television Picture Tubes, Cathode Ray Tubes or Magnetrons. 17. 85 Resistor elements/chips with TCR 5 ppm per degree centigrade Chip Resistors/Bulk Metal Film Resistors or Bulk Metal Resistors. 18. 28 Selenium Rectifier Plates of Grade E-25 Selenium TV Rectifiers. 19. 84, 85 Ferrite Permanent Magnets & unmagnetised blanks for Ferrite Permanent Magnets DC Micromotors up to 13.5 volts and not exceeding 20 watts rating. 20. 71 Synthetic quartz crystal blocks and blanks Mounted Piezoelectric crystals, 21. 39 Flexible folding disk jacket with liner Floppy diskettes. 22. 39 Glass epoxy or/and polya-mide pro-pregs Multilayer printed circuit boards, copper clad laminates. 23. 48, 76 Kraft paper/tissue paper or aluminium foil for voice coil Loudspeakers. 24. 48, 59 Lint free towels/paper Potentiometers, semicon-ductor devices, hybrid microcircuits, printed components. 25. 39, 73, 79, 85 Parts of magnetic sound heads Magnetic sound heads. 26. 39 Antistatic materials in the form of tubes, straps, bags, mats, covers, bins, boxes, containers Semiconductor....
X X X X Extracts X X X X
X X X X Extracts X X X X
....per plated steel wires of dia 0.04 mm to 1.1mm Capacitors, resistors (other than heating resistors), RF/IF coils, lead tabs. 16. 28, 34, 39, 48, 61, 68, 70, 82, 84, 85 (a) Mica and Micualex washers Semiconductor devices, silicon (in all forms) Hybrid Microcircuits. (b) Abrasive powder (c) Parts of doping systems (d) Plastic film for wafer dicing (e) Sputtor targets (f) Etch disc (g) Film Template (h) Special Gases: (i) Hydrogen chloride   (ii) 100%silane   (iii) Ammonia   (iv) Dichlorosilane   (v) Argon   (vi) Etch gas   (vii) Hexaluoroethane   (viii) 5% phosphine   in nitrogen    (ix) Freon 14   (x) 15% phosphine in   nitrogen    (xi) Helium   (xii) 15% Arsene in   hydrogen (xiii) Boron trifluoride   (xiv) Nitrogen in   lacture bottles    (xv) Sulphur hexaflo-   ride    17. 28, 37, 38, 39, 71, 73 (i) Bismuth lead-....
X X X X Extracts X X X X
X X X X Extracts X X X X
....z wire in the followisng sizes, namely :- (i) 24 (strands) x 0.03 mm (diameter of each strand) (ii) 12 (strands) x 0.03 mm (diameter of each strand) (iii) 9 (strands) x 0.04 mm (diameter of each strand) (iv) 6 (strands) x 0.04 mm (diameter of each strand) (v) 8 (strands) x 0.03 mm (diameter of each strand) (vi) (strands) x 0.03 mm (diameter of each strand) RF/IF Coils or transformers. 7. 74 Phosphor Bronze wire nettings (60 mesh and above) Cones, Spiders, Dust Caps for Loudspeakers. 8. 28, 29 (i) Electroless Nickel salts/ solutions (ii) Sodium Hypophosphite Glass to metal seals. Lead frames. 9. 84, 85 (i) Capstan shaft (ii) Bearings, Bushes Tape Deck Mechanisms. 10. 84, 85 (i) Sintered/Self-lubricating Bushes (ii) Screws, Gears, Collectors, Brush holders DC Micromotors upto 13.5 volts and not exceeding 20 watts rating. 11. 69, 85 (i) Ceramic plates/Flats/ cases bases/formers (ii) Steatite rods and bars in coated or uncoated form (iii) Alumina Rods and bars (with Alumina content above 90%) in coated or uncoated forms. Resistors (other than Heating resistors), Poten-tiometers, semiconductor Devi....
X X X X Extracts X X X X
X X X X Extracts X X X X
....ble PVC sleeving, tubing, film or ring Capacitors, semiconduc-tor devices, DC Micro-motors, relays, deflection components. 25. 39 Splicing tape Magnetic tape, cassettes. 26. 39, 48, 85 Insulating/taping material (including pocket carrier tape) in tape, roll or strip form with or without adhesive Capacitors, deflection components, resistors (other than heating resistors), printed circuit boards, potentiometers, semiconductor devices, inductors. 27. 85, 84, 58, 69 (i) Silicon carbide heating elements (ii) Molybdenum Silicide/Molybdenum disilicide heating elements (iii) Silicon carbide rollers (iv) Inconel steel rollers (v) Conveying trays (vi) TP Furnace and trays (vii) Saggers Ferrites, ceramic capaci-tors, potentiometers, semiconductor devices. 28. 32 Printing ink for printing on aluminum plates Decorative name plates for tape recorders 29. 27, 34, 39 (i) Silicon grease (ii) Cyanoacrylate or anaerobic sealants (iii) Molybdenum based lubricating compound (iv) Kilopoise lubricating grease Potentiometers, tape deck mechanisms, switches, relays, heat sinks, electronic valves and tubes 30. 28,69 (i....